121 lines
5.1 KiB
HTML
121 lines
5.1 KiB
HTML
|
|
<p>
|
|
<dfn>Auxiliary sends</dfn> are simple <a
|
|
href="@@processor-box">processors</a> in a bus or
|
|
track channel strip. They tap the signal at a specific point in the signal
|
|
flow (pre-fader, post-fader, before or after EQs and other plugins, etc.)
|
|
and send a copy of that signal to a bus, without affecting the
|
|
normal signal flow downwards to the channel fader.
|
|
</p>
|
|
<p>
|
|
Aux sends from several tracks are collectively sent to a
|
|
<dfn>bus</dfn> in Ardour, to create a monitor mix for a
|
|
musician, or to feed an effect unit. A bus used in this way is considered
|
|
an auxiliary bus or <dfn>Aux bus</dfn> even though it is the same as
|
|
any other bus. The output of such a bus might
|
|
be routed to separate hardware outputs (in the case of headphone or monitor
|
|
wedge mixes), or returned to the main mix (in the case of an effect).
|
|
</p>
|
|
<p>
|
|
Aux sends do not show up outside of Ardour either on the audio device
|
|
or as JACK ports, <a href="@@external-sends">External Sends</a> should
|
|
be used to send audio to the audio device or Jack ports. External Sends can
|
|
send the tapped signal somewhere else directly, which is not usually
|
|
possible on hardware mixers.
|
|
</p>
|
|
|
|
<p>
|
|
It may be useful to
|
|
<a href="@@comparing-aux-sends-and-subgroups">compare and contrast</a>
|
|
the use of aux sends with <a href="@@subgrouping">subgrouping</a>.
|
|
</p>
|
|
|
|
<h2>Adding a new aux bus</h2>
|
|
<p>
|
|
New busses can be created using the <kbd class="menu">Session > Add Track, Bus or VCA…</kbd>
|
|
menu, and selecting <kbd class="menu">Audio Busses</kbd> in the Template/Type
|
|
selector on the left of the <kbd class="menu">Add Track/Bus/VCA</kbd> dialog.
|
|
</p>
|
|
|
|
<h2>Adding a send to an aux bus</h2>
|
|
<p>
|
|
Context-clicking on the processor box for the track to send to the bus, and
|
|
choosing <kbd class="menu">New Aux Send …</kbd> shows a submenu, listing the busses.
|
|
Choosing one bus will add a send (which will be visible in the processor box).
|
|
Note that if the only existing bus is the Master Bus, the menu will be grayed out.
|
|
</p>
|
|
|
|
<h3>Pre-fader and Post-fader Aux Sends</h3>
|
|
<p>
|
|
Depending on whether the context-click happened above or below the fader in the
|
|
processor box, the new aux send can be placed before or after the fader in the
|
|
channel strip.
|
|
</p>
|
|
<ul>
|
|
<li><dfn>Post-fader</dfn> aux sends are typically used when using an aux for
|
|
shared signal processing (FX), so that the amount of effect is always
|
|
proportional to the main mix fader.</li>
|
|
<li><dfn>Pre-fader</dfn> sends ensure
|
|
that the level sent to the bus is controlled <em>only</em> by the send, not the
|
|
main fader—this is typical when constructing headphone and monitor wedge
|
|
mixes.</li>
|
|
</ul>
|
|
|
|
<p>
|
|
The color of the processor will reflect this pre/post position (red for
|
|
<span style="color:darkred;">Pre</span>, green for <span
|
|
style="color:darkgreen;">Post</span>). Dragging and dropping the send inside
|
|
the processor box before or after the Fader processor changes the type of
|
|
fader accordingly.
|
|
</p>
|
|
|
|
|
|
<h2>Adding a new aux bus and sending a Track Group to it</h2>
|
|
<p>
|
|
All members of a group can be sent to a new aux bus at once with a single click.
|
|
After creating the <a href="@@track-and-bus-groups">track group</a>
|
|
(and adding tracks to it), context-clicking on the group tab allows to choose either
|
|
<kbd class="menu">Add New Aux Bus (pre-fader)</kbd> or
|
|
<kbd class="menu">Add New Aux Bus (post-fader)</kbd>. A new aux bus will be created,
|
|
and a new aux send added to every member of the track group that connects to
|
|
this aux bus.
|
|
</p>
|
|
|
|
<h2>Altering Send Levels</h2>
|
|
<p>
|
|
The amount of the signal received by a send that it delivers to the bus it connects to
|
|
can be altered in two ways:
|
|
</p>
|
|
<h3>Using the Send Fader</h3>
|
|
<p>
|
|
Every send processor has a small horizontal fader that can be adjusted in the
|
|
usual way. It is not very big and so this can be a little unsatisfactory if
|
|
a very fine control over the send level is required.
|
|
</p>
|
|
<h3>Map Aux Sends To Main Faders</h3>
|
|
<p>
|
|
In Mixer mode, pressing the button marked <kbd class="menu">Show Sends</kbd> on a aux bus will
|
|
alter the channel strip for every track or bus that feeds the aux bus. Many
|
|
aspects of the strip will become insensitive and/or change their visual
|
|
appearance. More importantly, the main fader of the affected channel strips
|
|
will now control the send level and <strong>not</strong> the track gain.
|
|
This gives a larger, more configurable control to alter the level. Clicking the
|
|
<kbd class="menu">Show Sends</kbd> button of the aux bus again reverts the
|
|
channel strips to their normal use.
|
|
</p>
|
|
|
|
<h2>Disabling Sends</h2>
|
|
<p>
|
|
Clicking on the small LED in the send display in the processor box of the
|
|
channel strip will enable/disable the send. When disabled, only silence will
|
|
be delivered to the aux bus by this track. When enabled, the signal arriving
|
|
at the send will be delivered to the aux bus.
|
|
</p>
|
|
|
|
<h2>Send Panning</h2>
|
|
<p>
|
|
Send panners can be configured to either be independent of the main
|
|
panner, or to follow it. The latter could be useful for Reverb effects, or
|
|
for in-ear monitor mixes delivered in stereo.
|
|
</p>
|