112 lines
4.8 KiB
HTML
112 lines
4.8 KiB
HTML
---
|
|
layout: default
|
|
title: Aux Sends
|
|
---
|
|
|
|
<p>
|
|
<dfn>Auxilliary sends</dfn> are <a
|
|
href="/working-with-plugins/processor-box/">processors</a> in a bus or
|
|
track channel strip. They tap the signal at a specific point in the signal
|
|
flow (pre-fader, post-fader, before or after EQs and other plugins, etc.)
|
|
and send a copy of that signal somewhere else, without affecting the
|
|
normal signal flow downwards to the channel fader.
|
|
</p>
|
|
<p>
|
|
Usually, aux sends from several tracks are collectively sent to a
|
|
dedicated <dfn>Aux bus</dfn> in Ardour, to create a monitor mix for a
|
|
musician, or to feed an effect unit. The output of such a bus might
|
|
be routed to separate hardware outputs (in the case of headphone or monitor
|
|
wedge mixes), or returned to the main mix (in the case of an effect).<br
|
|
/>
|
|
Since sends are JACK ports, it is also possible to send the tapped signal
|
|
somewhere else directly, which is not usually possible on hardware mixers
|
|
(see <a href="external-sends/">External Sends</a>).
|
|
</p>
|
|
|
|
<p>
|
|
It may be useful to
|
|
<a href="/signal-routing/comparing-aux-sends-and-subgroups">compare and contrast</a>
|
|
the use of aux sends with <a href="/signal-routing/subgrouping">subgrouping</a>.
|
|
</p>
|
|
|
|
<h2>Adding a new aux bus</h2>
|
|
<p>
|
|
Choose <kbd class="menu">Session > Add New Track or Bus</kbd>. In the
|
|
<kbd class="menu">New Track & Bus</kbd> dialog, select "Busses" in the Track/Bus
|
|
selector at the upper right.
|
|
</p>
|
|
|
|
<h2>Adding a send to an aux bus</h2>
|
|
<p>
|
|
Context-click on the processor box for the track you want to send to the bus, and
|
|
choose <kbd class="menu">New Aux Send</kbd>. From the submenu, choose the bus you
|
|
want to send to. A send will be added (and will be visible in the processor box).
|
|
Note that the submenu may be empty if you have not created a bus yet.
|
|
</p>
|
|
|
|
<h3>Pre-fader and Post-fader Aux Sends</h3>
|
|
<p>
|
|
Depending on whether you context-click above or below the fader in the processor box,
|
|
the new aux send can be placed before or after the fader in the channel strip.
|
|
<dfn>Post-fader</dfn> aux sends are typically used when using an aux for shared signal
|
|
processing (FX), so that the amount of effect is always proportional to
|
|
the main mix fader. <dfn>Pre-fader sends</dfn> ensure that the level sent to the bus
|
|
is controlled <em>only</em> by the send, not the main fader — this is typical
|
|
when constructing headphone and monitor wedge mixes.
|
|
</p>
|
|
|
|
<h2>Adding a new aux bus and sending a Track Group to it</h2>
|
|
<p>
|
|
You can add aux sends to all members of a group and connect them to a new aux bus
|
|
with a single click. After creating the track group (and adding tracks to it),
|
|
context-click on the group tab and choose either
|
|
<kbd class="menu">Add New Aux Bus (pre-fader)</kbd> or
|
|
<kbd class="menu">Add New Aux Bus (post-fader)</kbd>. A new aux bus will be created,
|
|
and a new aux send added to every member of the track group that connects to
|
|
this aux bus.
|
|
</p>
|
|
|
|
<h2>Altering Send Levels</h2>
|
|
<p>
|
|
You can alter the amount of the signal received by a send that it delivers to the bus
|
|
it connects to. There are two approaches to this:
|
|
</p>
|
|
<h3>Use the Send Fader</h3>
|
|
<p>
|
|
Every send processor has a small horizontal fader that can be adjusted in the usual way. It is
|
|
not very big and so this can be a little unsatisfactory if you want very fine control
|
|
over the send level.
|
|
</p>
|
|
<h3>Mapping the Main Fader</h3>
|
|
<p>
|
|
Double-clicking on the send in the processor box will allow you to use the
|
|
big fader of the mixer strip to control the send. The visual appearance of
|
|
the mixer strip will change to reflect this. Double-click the send again to
|
|
revert back to normal function for the strip.
|
|
</p>
|
|
<h3>Map Aux Sends To Main Faders</h3>
|
|
<p>
|
|
Pressing the button marked <kbd class="menu">Aux Sends</kbd> on a aux bus will
|
|
alter the channel strip for every track or bus that feeds the aux bus. Many
|
|
aspects of the strip will become insensitive and/or change their visual
|
|
appearance. More importantly, the main fader of the affected channel strips
|
|
will now control the send level and <strong>not</strong> the track gain.
|
|
This gives a larger, more configurable control to alter the level. Click the
|
|
<kbd class==menu">Aux Sends</kbd> button of the aux bus again to revert the
|
|
channel strips to their normal use.
|
|
</p>
|
|
<h2>Disabling Sends</h2>
|
|
<p>
|
|
Clicking on the small "LED" in the send display in the processor box of the
|
|
channel strip will enable/disable the send. When disabled, only silence will
|
|
be delivered to the aux bus by this track. When enabled, the signal arriving
|
|
at the send will be delivered to the aux bus.
|
|
</p>
|
|
<h2>Send Panning</h2>
|
|
<p>
|
|
Send panners can be configured to either be independent of the main
|
|
panner, or to follow it. The latter could be useful for Reverb effects, or
|
|
for in-ear monitor mixes delivered in stereo.
|
|
</p>
|
|
|