13
0
livetrax/manual/xml/synchronization_concepts.xml
Paul Davis 45d3ec1437 merged with 1697 revision of trunk (which is post-rc1 but pre-rc2
git-svn-id: svn://localhost/ardour2/branches/2.1-staging@1698 d708f5d6-7413-0410-9779-e7cbd77b26cf
2007-04-11 13:07:51 +00:00

171 lines
7.8 KiB
XML

<?xml version="1.0" standalone="no"?>
<!DOCTYPE section PUBLIC "-//OASIS//DTD DocBook XML V4.4//EN" "http://www.oasis-open.org/docbook/xml/4.4/docbookx.dtd" [
]>
<section id="sn-synchronization_concepts">
<title>Synchronization Concepts</title>
<para>
As soon as you start handling audio on more than one device, it is
important to understand and to think about
<emphasis>synchronization</emphasis> : how to get the devices to have
the same sense of time and speed.
</para>
<para>
However, there are two fundamentally different kinds of synchronization:
</para>
<section id="sample-clock">
<title>Sample Clock</title>
<para>
As outlined in the <emphasis>introductory concepts</emphasis> section,
digital audio is created by taking a "sample" of an analog signal
level on a periodic basis, say 48000 times per seconds (the "sample
rate"). A dedicated clock (the "sample clock") ((actually, an
oscillating crystal, but technology people call such things clocks))
"ticks" at that rate, and every time it does, a new sample is
measured. The way the clock is used to convert digital audio back to
an analog signal (i.e. to be sent to some loudspeakers) is more
complex, but the clock is still an absolutely fundamental part of the
mechanism.
</para>
<para>
Whenever you connect two digital audio devices together in order to
move audio data from one to the other, you <emphasis>must ensure they
share the same sample clock</emphasis> . Why is this necessary? The
oscillating crystals used for the sample clock are generally very
stable (they always tick at the same speed), but there are always
minute differences in the speed that any two clocks tick at. When used
by themselves, this makes no difference, but connect two digital audio
devices together and these minute differences will eventually
accumulate over time. Eventually, one of the devices will be trying to
read a sample "in the middle" of the other device's tick, and the
result is a small click or pop in the audio stream.
</para>
</section>
<section id="timeline-sync">
<title>Timeline Sync</title>
<para>
The concept of a timeline comes up over and over again when working
with a digital audio workstation, and also with video editing systems.
By "timeline" we mean nothing more than some way to define a "name"
for the point where certain sounds (and/or visual images) occur. When
you work in Ardour's editor window, the rulers near the top provide
one or more timelines in different units. You can look at the editor
window and say "this sound starts at 1 minute 32 seconds" or "this
tracks fades out starting at bar 13 beat 22".
</para>
<para>
But what happens when you want to share a timeline between two
different devices? For example, you may want to run a hardware video
editor in conjunction with ardour, and always have the visual and
audio playback be at the same point "in time". How do they each know
what "in time" means? How do they know where the other one is? A
mechanism for answering these questions provides <emphasis>timeline
synchronization</emphasis> .
</para>
<para>
Timeline synchronization is entirely different from sample clock
synchronization. Two devices can share a sample clock, but never use
timeline information. Two devices can be sharing timeline information,
but run on different sample clocks - they might not even have sample
clocks if they are analog devices.
</para>
</section>
<section id="word-clock">
<title>Word Clock</title>
<para>
"Word Clock" is the name given to a signal used to distribute the
"ticks" of a sample clock to multiple devices. Most digital audio
devices that are intended for professional use have a word clock
connector and a way to tell the device to use either its internal
sample clock (for standalone use), or to use the word clock signal as
the sample clock. Because of the electrical characteristics of the
signal, it is very important that any length of cable used to
distribute word clock is "terminated" with a 75 ohm resistor at both
ends. Unfortunately, some devices include this terminator themselves,
some contain a switchable resistor and some do not. Worse still, the
user manuals for many devices do not provide any information on their
termination configuration. It is often necessary to ask the
manufacturer in cases where it is not made very obvious from marking
near the word clock connectors on the device.
</para>
</section>
<section id="timecode">
<title>Timecode</title>
<para>
"Timecode" is a signal that contains positional or "timeline"
information. There are several different kinds of timecode signal, but
by far the most important is known as SMPTE. Its name is an acronym
for the Society for Motion Picture T?? Engineering, and timecode is
just one of the standards they defined, but its the most well known.
Because of its origins in the film/video world, SMPTE is very centered
on the time units that matter to film/video editors. The base unit is
called a "frame" and corresponds to a single still image in a film or
video. There are typically on the order of 20-30 frames per second, so
the actual resolution of SMPTE timecode is not very good compared to
audio-based units where there are tens of thousands of "frames" per
second.
</para>
</section>
<section id="SMPTE">
<title>SMPTE</title>
<para>
SMPTE defines time using a combinations of hours, minutes, seconds,
frames and subframes, combined with the frame rate. In a film/video
environment, SMPTE is typically stored on the film/video media, and
sent from the device used to play it. There are different ways of
storing it on the media - you may come across terms like LTR and VTC -
but the crucial idea to grasp is that the film/video has a timecode
signal "stamped" into it, so that it is always possible to determine
"what time it is" when any given image is visible.
</para>
<para>
SMPTE timecode is sent from one system to another as an analog audio
signal. You could listen to it if you wanted to, though it sounds like
a generally screeching and unpleasant noise. What the SMPTE standard
defines is a way to encode and decode the
hrs:mins:secs:frames:subframes time into or from this audio signal.
</para>
</section>
<section id="mtc">
<title>MTC</title>
<para>
The other very common form of timecode is known as "MTC" (MIDI Time
Code). However, MTC is actually nothing more than a different way to
transmit SMPTE timecode. It uses the exact same units as SMPTE
timecode, but rather than send the signal as audio MTC defines a
transmission method that uses a MIDI cabable and a data protocol. MTC
consumes a measurable, but small, percentage of the available
bandwidth on a MIDI cable (on the order of 2-3%). Most of the time, it
is wise to use a single cable for MTC and MMC (MIDI Machine Control)
and not share it with "musical" MIDI data (the kind that an instrument
would send while being played).
</para>
</section>
<section id="jack-transport">
<title>JACK Transport</title>
<para>
For Ardour and other programs that use <emphasis>JACK</emphasis>,
there is another method of doing timeline synchronization that is not
based on SMPTE or MTC.
</para>
</section>
<!--
<xi:include xmlns:xi="http://www.w3.org/2001/XInclude"
href="Some_Subsection.xml" />
-->
</section>