Changes handle_cursor_right_press() in PluginSubviewState to pure virtual
function so that PluginSelect and PluginEdit can each have their own
version.
The cursor_left and cursor_right mackie control buttons will now move the
sends subview left and right like it does in the plugin subview. Previously,
if you had more than 8 sends (which is almost always the case for Mixbus),
then sends 9+ were unreachable on an 8 channel controller.
This commit fixes an issue where if your controller was currently on a
bank not near the first few tracks, and you then deleted tracks, the
controller bank buttons would appear unresponsive because of the
"if (initial >= sorted.size())" check in switch_banks().
This would occur when the difference between the _initial_bank and
whatever sorted.size() returns was greater than or equal to strip_cnt.
For example, if your _initial_bank was 48, your strip_cnt was 24 and you
had 24 tracks after the deletion, then the above conditional would evaluate
to true and exit out of switch_banks BEFORE actually switching the bank,
effectively stranding the controller unless you added enough tracks back.
If the QCon ProG2 is selected as the device profile, then the button map
will be built with handlers that map specific to the iCon QCon ProG2
controller.
Adds function to clear solo and (with shift) mute all channels.Adds
function to save and (with shift) save as. Adds function to toggle all
processors on selected track. Adds functions to select track to the
left/right. Adds function to add marker and (with shift) remove marker at
playhead. Adds function to undo without needing shift modifier.
Adds a function to go to the next and previous marker. Adds a function to
redo (without requiring a shift modifier). Adds a function to open a
project.
Adds a device profile for iCon Platform M+ controller and new function
that flips between editor and mixer window. This function is mapped to
"mixer" button on controller.
TempoMap::use() assumes the thread_local pointer has been set up. This
is not the case for the control protocol event loop, so call ::fetch()
instead which does not require this assumption (and sets the thread_local
pointer too, though nothing else in the Mackie code uses it)
Strip::notify_property_changed accesses _stripable without verifying
that is not null. However it is possible for this to be null, so
add a null check.
Only enable the master display and meter modes for Qcon devices if this
surface is in the master position. Extenders don't have master meters
or master displays.
Logic to detect an extender has to be based on if this surface object is
the master position. Has master fader is true for all surfaces in this
"device".
Old and new strings are compared before sending to keep traffic down. To
ensure that we send all the required characters be sure to init the last
value to characters that are never going to appear in a real string.
Space is a bad choice since it is a valid character. Use NUL instead.
The device info file allows key names and values to be configured in each
device file. Use that information when building the Functions Keys tab in
the Mackie protocol setup dialog.
While surfaces are being created it is possible to have surfaces, but
not have a master surface yet. This happens when the config calls
for extenders to the left of the master section. Don't assume that
if we have surfaces, the master surface is available.
This resolves a PBD vs ARDOUR namespace error for some compilers:
```
error: reference to 'microseconds_t' is ambiguous
libs/pbd/pbd/microseconds.h:29:19: error: candidates are: typedef uint64_t PBD::microseconds_t
libs/ardour/ardour/types.h:81:29: error: typedef PBD::microseconds_t ARDOUR::microseconds_t
```
If the wrong device profile is selected (ex Xtouch One) but another device
is connected (Xtouch), it is possible to have a master fader on the
device, but not in the code. This would then cause a crash when the
master fader was touched.
This just protects from a wrong configuration.
