Demote configurations if they have mismatched midi in or out with the
same mechanism as for audio, but with lower coefficients so that
mismatched midi has less influence than mismatched audio in selecting
the best configuration.
POLICY CHANGE.
Just refuse configurations without any output at all, and let the
remaining logic take care of selecting configurations with no audio
output if they make sense and there are no better configurations.
POLICY CHANGE: configurations with no output might now be considered
even if they have audio inputs (e.g. a pure pitch detector without audio
passthrough), whereas they were skipped before.
Instead of uniformly demote configurations with a non-matching audio
input count (using a penalty offset of 1000), also grade the
impreciseness of the configuration so that those with the nearest input
count are preferred. As for outputs, give a slightly higher handicap to
configuration with too many inputs with regard to the actual audio
inputs that can be fed to the plugin.
POLICY CHANGE: when only imprecise configurations are found the actually
selected one can be different (better) than before this commit.
Just make the code responsible for possible_in > 0 also handle
possible_in == 0 since it nearly does the same thing.
The only difference is that the possible_in == 0 case didn't check at
all for audio_in, essentially acting as if possible_in was audio_in.
There is thus a small POLICY CHANGE, but the selected configuration will
stay the same unless a better matching configuration is available.
Still no policy change, since when a configuration is chosen that would
have belonged to the second pass, then its penalty will be increased by
1000 and it will be selected only as last recourse.
This doesn't change the policy since configurations are given an
additional 1000 penalty if audio_in != possible_in, and will thus be
trumped by any "precise" configuration (unless the latter has 1000
excess or missing outputs which should be less than likely).
Instead of setting \imprecise at the end of the loop if a configuration
was found (which clobbered valuable information, see dae2406187), set it
each time a new configuration is chosen.
In the second loop that tries harder, resetting \imprecise also avoids a
previous "imprecise->set(AUDIO, 0)" to last even if another
configuration is chosen later.
Last but not least, it will enable correctly setting the midi input
count hoped for by the configuration.
Merge the cases in == -1 and in == -2 since those are both wildcards,
almost symmetric in the AU spec, and handled completely symmetrically by
the code here considering it accepts invalid or unspecified demands.
Also merge the cases in > 0 and in < -2 since they are handled exactly
the same as far as outputs are concerned.
That code modifies \imprecise if it is not NULL, but
- if a configuration is found, \imprecise will be set to in, clobbering
the tentative changes done here;
- if a configuration is not found, a last-resort loop will be run that
will set the same member of \imprecise, also clobbering our changes.
Remove it since it does nothing that is looked at before being
forgotten. A way to get the intended outcome will be introduced later.
...to later enable that condition truthiness to depend on the
loop iteration. The goal here is to prepare for the upcoming rewrite,
without introducing any policy change for now.
There is no behavior change because if all loop iterations are skipped,
then \found will be false, and with \imprecise being null the last
attempt will be skipped and we will return false.
Instead of doing an initial loop for detection of exact matches, then
letting the following loop set \audio_out yet ignore its value, merge
the two loops but give exact matches a negative penalty so that the
\audio_out value they set won't change afterwards.
No policy change.
Since can_replicate is true at loop start, and in the loop body there is
a break; after every can_replicate=false, there's no point to test its
value in the loop condition.
There is no code that read the set value in between the removed line and
its exact counterpart below. There is no similar duplicate in the
AudioUnit code due to the way AudioUnit handles midi.
The original LV2 state extension required that run() is suspended during
restore(). Ardour violates this rule, which can lead to crashes and
other issues.
The state extension has been updated to allow restoring state in a
thread-safe way by using the worker to enqueue state changes. This
commit supports that new specification, i.e. supports dropout-free state
restoration properly.
However, the bug with old plugins that do not use this facility is still
not fixed.
A peak rectangle in the mixer strip is ruled by "gtk_bright_indicator". In the previous commit I mixed up this item with "meterbridge label" & "meterbridge peakindicator". This commit changes "gtk_bright_indicator" from white to red and returns "meterbridge label" & "meterbridge peakindicator" state to primordial. So now the peak rectangle in the mixer strip will be red when a sound peak has a place.
